Versions Compared

Old Version 7

changes.mady.by.user Stefanie Schröder (Unlicensed)

Saved on

compared with

New Version Current

changes.mady.by.user Stefanie Schröder (Unlicensed)

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.


Comparison Group

Several bullet graph components can be scaled identically by using the same Comparison Group, which is activated by the checkbox. The comparison group will then be shown during design time on the top right corner of the component. That way the minimum and maximum of the data basis in this group is used.

Comparison groups are used globally within the BIApp, ie also graphomate charts, graphomate tiles as well as deviation charts in the graphomate tables are scaled identically by using the same comparison group abbreviation.

Category Labels

This section controls the labels of the bullet graphs. If the first checkbox is activated, the category labels are displayed for each bullet graph.

Center Category Labels

Trailing Category Labels

If the last checkbox is activated, repeating category labels will be suppressed.  

Value Axis

This option controls the display of the value axis. Always draws one value axis for each bullet graph; Once draws a single value axis, which applies to all bullet graphs. This appears at the bottom of the component above the footer. Never suppresses the display of the value axis completely.

Tick Interval

This value governs the ticks along the value axis. If e. g. a 5000 is entered, a tick is displayed at 5000, 10000, 15000 etc. The default 0 generates an appropriate number of ticks for the available space. Currently, normalized data (see next option) is not supported. Please note that rendering is slowed down considerably if the data is very large, and a small tick interval is entered.

Normalize to Target

If the option Normalize to Target Value is activated, all values will be normalized to a single value which can be selected from the dropdown box Target Series. The selected value will be interpreted as 100%; all other values are calculated into percentages accordingly. If the property Value Axis is set to Always, the underlying values will be displayed, if set to Once, the value axis will display the calculated percentages. This option is deactivated if the component is registered in a comparison group.

Use Individual Scales

If this checkbox is activated, each bullet graph's axis is calculated individually. Otherwise, all bullet graphs are scaled identically. When choosing Value Axis option Once, Use Individual Scales is disabled, as is the case if the component is registered in a comparison group.

Reverse Quantitative Ranges

This checkbox controls the representation of the axis. If this option is activated, the axis is drawn from n to 0, otherwise the scaling is inverted – from 0 to n.

...

Category Labels

This

...

section controls the

...

labels of the bullet graphs

...

.

...

Image RemovedImage RemovedImage Removed

...

If the

...

first checkbox is activated,

...

If the option Performance Values is activated the values of the Performance Measure 1 are displayed at the end of the corresponding bar. All other values can be seen by using the Tooltips.

With the option Deviations, bars that visualize the deviation between Performance Measure 1 and Comparative Measure 1 can be toggled on and off.

Reverse Qualitative Ranges

This checkbox controls the display of the Qualitative Ranges. If this option is deselected, they are drawn from the left side (usually the value range minimum) to the input value (or calculated value). If the option is activated, the Qualitative Ranges are displayed in reverse so that the range is drawn from the input value to the value range maximum.

Micro Pies

Activating this Checkbox will display a pie chart in front of each bullet graph. This small pie displays the percentage of the primary measure as part-to-whole – the sum of the primary measure.

If a total exists in the data source, it is used as a basis for the calculation. If only partial or no sums are available, the total amount will be calculated from the data.

The diameter of the Micro Pies can be changed with the option Diameter of Micro Pies. The color of the Micro Pies can be selected with the option Micro Pie Color.

Calculate Qualitative Ranges

If this Checkbox is activated, Qualitative Ranges 1 and 3 will be calculated.

The values of Percentage for Qualitative Range 1 and 3 are used to calculate Qualitative Ranges 1 and 3 based on Qualitative Range 2.

The two missing ranges are calculated by multiplying range 2 by the values entered here. Therefore the first value should be < 1, as otherwise the bar for Qualitative Range 2 will be obscured by the bar for Qualitative Range 1.

...

the category labels are displayed for each bullet graph.

Center Category Labels

If this option is active, category labels are centered in front of/above the bullet graph bars.

Trailing Category Labels

If activated, the category labels will be shown behind/below the bars. Otherwise, the labels will be placed in front of/above the bars.

If the last checkbox is activated, repeating category labels will be suppressed.  

Chart Alignment

This checkbox describes the orientation of the bullet graphs. If it is activated, they are displayed vertically, otherwise they are displayed horizontally.  

Image AddedImage AddedImage Added

Image Added